How to Program Garage Door – Remote and Keypad

So you have a new car and want to try your garage door technology and program your remote. Sounds simple, right? Not until you try and it does not work. A garage door remote allows you to conveniently open or close the garage door without the need to get out of the car. Alternatively, you can also set up the outside keypad. If you replace your garage door opener or if it breaks or is lost or stolen, you may need to be familiar with how to program garage door.

How to Program Garage Door

How to Program Garage Door

When it comes to DIY Garage door repair, it’s important to inspect and maintain your garage door from time to time. At one point you may need to program the garage door as well. The instructions on how to program garage door keypad vary from one model to another. Whether you are having a garage door expert help you, or you’d like to do the programming yourself, below is a step-by-step guide to successfully do the job. 

Programming a Garage Door Operator Remote or Outside Keypad

Chamberlain, Liftmaster, and Sears Craftsman (971LM and 973LM, 371LM and 373LM Security Plus Transmitters)

  1. On the garage door opener motor unit is a smart button – press then release it. The indicator light will turn on for 30 seconds. For certain remotes, the corresponding learn button is amber or red and square. For others it is purple and square.
  2. Press the button on the handheld remote and hold within 30 seconds.
  3. Once the light of the motor unit blinks, release the button – it has already learned the code. You will hear two clicks if light bulbs are not installed.

Liftmaster and Sears Craftsman Wireless Keypads 

  1. On the garage door opener motor unit is a smart button – press then release it. The indicator light will turn on for 30 seconds.
  2. Enter your preferred four-digit PIN on the keypad within 30 seconds. Press and hold the ENTER button after.
  3. Once the motor unit blinks, release the button – it has already learned the code. You will hear two clicks if light bulbs are not installed.

Programming Genie Remotes and Keypads

Genie Intellicode Remote Transmitters

  1. On the door operator’s powerhead receiver is the Receiver Learn Code button– press it once. The indicator light will blink red for 30 seconds.
  2. Press the transmitter button thrice. Make sure to keep the transmitter you want to tune at least two feet away from the powerhead during the process.
  3. Press the transmitter button one more time.

Genie Digital Remote Transmitters with Internal Set Switches

To program these remote transmitters, you just need to match the settings (including frequency) on the internal code setting switches with the same set in the garage ceiling’s receiver, which is found behind the light lens of the motorhead or inside the external small rectangular box on the ceiling.

Genie Multi-Button Digital Remotes with Internal Set Switches

  1. Match the settings (including frequency) on the internal code setting switches with the same set in the garage ceiling’s receiver.
  2. Change the small programming switch to ‘S’, then press the transmitter button you want to assign to the door.
  3. Put the programming switch back to ‘R’, then press the assigned transmitter button to test it.

Genie Garage Door Opener Keypads

  1. Reset the keypad: start by sliding the cover halfway up. Press the buttons # and 8 and simultaneously slide the cover up. Release the buttons – if the backlit keypad light steadily glows, proceed to step 2; otherwise, close the pad cover and reopen until you hear a click.
  2. Press buttons 3, 5, 7, and #, respectively.
  3. Enter your preferred PIN, and then press #. Remember to use only numbers and not # and *.
  4. Enter the Door code and press the * button.
  5. Slide the pad cover down. Test the PIN.

Multiple Genie Garage Door Opener Programming for GWKP

Note: All garage doors use the same PIN.

  1. Enter your PIN and then press PROG. The red LED light will blink once per second.
  2. Press PROG one more time. The red LED light will blink two times per second.
  3. Press the number of doors you want to command. Then press PROG, and the red LED light will blink several times before it turns off.
  4. Determine which will be door #1, #2, and so on.
  5. On the motor head is the Learn Code button – press it.
  6. Enter your PIN and then press the Up/Down button on the keypad.
  7. Press the number for this door opener, then press the Up/Down button.
  8. Repeat steps 5 to seven for each door opener.

Questions

Can you Reprogram a Garage Door Remote?

How to Program Garage Door

Yes, you can! If the garage door is hard to open, there may be a malfunction, so you may need to reprogram the remote. The process is simple. Start by visiting the website of the manufacturer and look for the remote programming instructions. You can also follow the step-by-step guide above that corresponds to the model or brand of your garage door. 

How do I Program my Overhead Garage Door Remote?

Below are the instructions on how to program overhead garage door remote clicker:

  1. Press the overhead garage door opener unit’s Learn button and release it. The indicator light will turn on steadily for 30 seconds.
  2. Press the button on the handheld remote and hold within 30 seconds.
  3. Once the light of the overhead unit blinks, release the button – it has already learned the code.

To Summarize

Depending on several factors, such as the manufacturer of your garage door and whether you are programming a remote, keypad, or in-car remotes, programming instructions will vary from one garage door to another. There are also various types of garage door openers that will help quiet when you open and close it. Learning how to program garage door is relatively easy and is useful for when you need to change your garage door opener. We hope this guide helps you do the job easily and hassle-free. 

How to Tell if Garage Door Spring is Broken

Your garage is a big part of your home aesthetics and security as well. You need it operating correctly so that you can have peace of mind. It is a bad decision if you keep opening the door when it is faulty. It might fail entirely, and you will spend a fortune to get it back up and running. To be proactive about it, you have to know how to tell if garage door spring is broken. 

How To Tell If Garage Door Spring Is Broken
How To Tell If Garage Door Spring Is Broken

How to Tell if Garage Door Spring is Broken

Lucky for you, this post will help you know whether your garage door is broken or faulty. You will also learn the importance of the door springs and why you should keep them in perfect condition. Although before you decide to fix the issue yourself, it’s important to preface yourself with garage door safety tips before doing anything. 

Why Garage Door Springs are Important

Typically, garage doors are heavy. If you are left to lift them, you will break your back before moving the door an inch. That is why the door springs are very crucial to the operation of the door. They make it easy to either automatically or mechanically lift the door. There are two types of garage door springs, but that is a subject for another day. 

Signs of a Broken or Faulty Garage Door Spring

You should not sit and wait for your door to run into problems. Experts recommend that you check the springs at least once a month and troubleshoot for potential problems. When looking for spring problems, these are the signs you should look out for:

  • When the door cannot open manually: If your door is dedicated to manual opening, it should not give you any trouble while opening it. If yours is an automatic opening system, turn it off for a short while and try opening the door manually. It should be easy to do it. However, if it is extremely difficult to open the door; you may be looking at a broken or faulty spring. 
  • Any signs of tear and wear are indications that things are not alright with the springs: Do a physical check on all hardware and be keen to note that their shapes are perfect. Any signs of knocks and misalignment are clear messages of damage to the springs. 
  • If the safety reversing mechanism is not working: For automatic opening doors, you can test if the springs are functional by hitting the button for it to close and then stand in its way as it closes with your hands stretched. The door should automatically reverse when there is an obstruction in its path. If this does not happen, the biggest suspect could be the springs. 
  • If the door does not open or close at all, there is a problem: While this does not directly point to a spring problem, you cannot rule it out yet if your garage door is hard to open or won’t move at all. Get in touch with an expert and schedule an inspection to help you know and solve the problem. 

Bottom Line

You can never have a peaceful night sleep when your garage door has some sort of problems. You should learn how to tell if garage door spring is broken and taking the necessary action to repair it with some garage door repair tips before something worse happens to the largest moving part in your home. Worst comes to worst, you can reach out to a local garage door repair specialist to ensure that your garage door spring is up and running in no time. 

Garage Door Repair Tips

There are several reasons why garage door maintenance is so important. First is to ensure your safety and security, as your garage door is one way to enter your house. Your garage door should be in a well-functioning order to serve its purpose, and it also adds to your curb appeal. To maintain your garage door, performing an annual inspection is a must. If you find small damages here and there, knowing some garage door repair tips will surely help.

Garage Door Repair Tips
Garage Door Repair Tips

Garage Door Repair Tips

A few basic maintenance steps can be done during your annual inspection. The following simple checks will give you the know-how on how to fix garage door alignment and help you recognize and prevent simple damages.

Inspect the Tracks

The tracks should work with your garage door for many years to come. To make sure they do, it is essential to check them for dents or other damage. For minor dents, use a rubber hammer to pound it into place. For major damages, however, you might want to consider replacing the tracks altogether.

Cleaning and clearing the tracks from all debris is next. Get rid of dirt and dust using a large paintbrush, then wipe out the tracks using a household cleaner.

Aside from checking the tracks for damages and debris, see if they are correctly aligned and level. If they are, well and good; otherwise, you need some tips on how to align my garage door. Loosen the mounting brackets first, then tap the tracks so they are perpendicular with each other, tilting a little towards the back of the garage.

Lubricate the Machines

A basic part of garage door maintenance is lubricating pulleys, rollers, and tracks. It can be done by simply using a garage door lubricant powder or spray for your tracks and pulleys. For the rollers, you can use simple household lubricating oil. This is a simple fix for when your garage door may be hard to open or when it jerks while opening and closing

Tighten Loose Pieces

Finally, ensure that all bolts, fasteners, and nuts are tight in place. If you ever come across loosely installed pieces during an inspection, tighten them as soon as possible; procrastination may lead to forgetting it altogether.

Consult Professional Garage Door Repair Service 

Those basic garage door maintenance tasks are easy to follow for your DIY inspection; however, some tasks require the skills of a professional. Problems that warrant a garage door repair service include the following:

  • If your automatic garage door opener is having issues with the built-in safety reversal features, as such problems can compromise your car and your safety when not attended immediately.
  • If your garage door has a central spring that needs to be repaired or replaced. The central spring consists of high-tension springs, and trying to remove them can result in an accident and serious injury.
  • If your garage door has major or complicated damage such as a large dent that warrants the help of a professional or requires total replacement and garage door tune up cost.

Questions

How often do garage doors need maintenance?

Generally, garage door maintenance is done annually. How often you need to lubricate depends on the garage door parts. The rail needs lubrication once a year, but for hinges, rollers, springs, and tracks, it is advisable to grease them quarterly.

How can I make my garage door quieter?

There are a few ways to keep your garage door quiet:

  • If your garage door opener is chain-driven, change it to a belt-driven type.
  • If you have steel rollers, replace them with nylon type.
  • Change your extension spring system to torsion springs, which are installed above the door and are quieter.

Are you supposed to lubricate garage door springs?

Lubricating all moving parts every six months is essential to minimize wear and keep the door quiet. When lubricating, avoid products like spray lithium grease and oil, which are more affordable but do not penetrate deeply. These products also tend to pick up dirt and dust easily – something you do not want your garage door spring to have.

Bottom Line 

These basic garage door repair tips, such as how to fix garage door off track, can go a long way with regards to your safety and security and saving dollars for repair and replacement. An annual inspection of your garage door is advised, and you are encouraged to DIY simple maintenance steps. However, when it comes to more complicated maintenance and repair tasks, consider calling a professional garage door specialist for help to avoid accidents and injuries. After all, what matters more than money is your safety!

How to Tighten Garage Door Chain

A garage door chain plays a very important role in keeping the garage door well operated and managed. You also have to make sure that the garage door chain is properly tightened to prevent any serious injuries or death from the moving garage door. When the garage door chain loosens up, it can cause accidents. So, you have to make sure that the garage door chain is tight. But the main question is, how to tighten the garage door chain? 

how to tighten garage door chain

How to Tighten Garage Door Chain

To know more about this and how you can do that, read on. Below, we have provided a complete step by step process by which you can adjust the chain tension and tighten it, whenever needed.

Steps to Adjust the Chain Tension

Step #1: First you have to run the opener using the remote control or the door button. 

Step #2: Now disconnect the garage door first from the opener. If you have square rail opener, you have to pull the red manual for releasing the rope straight down and then take it back towards the motor unit. This will allow you to close as well as open the door by hand.

Step #3: With the help of two nuts and a threaded shaft, you can adjust the tension of the chain. The shaft and nuts are located on the inner trolley. If you are inside the garage looking toward the outside, then you will find these nuts for adjustment on the left-hand side of the rail. You have to loosen the outer nuts unless and until the chain droops down below the rail’s base. Then you have to loosen the inner nut to tighten the chain.

Step #4: For adding tension to the chain, you have to tighten the outer nit. With every turn you make on the outer nut, that chain will rise a little. You have to keep an eye on the midpoint of the rail. When the chain is about 1/2inch for the T-Rail and 1/4inch for the Square Rail above the base of the rain, you have to tighten the inner nut. 

So, these are some of the steps that you have to follow to tighten the garage door chain if you run into a basic garage door problem. It is very important to maintain this tightness to ensure better safety and security of the garage door. Garage door is the largest moving body in the house and it can cause many injuries in case of accidents. 

Bottom Line

If you were wondering about how to tighten the garage door chain, follow these aforementioned steps to tighten the garage door. It is also important to make sure that you are doing it in the right way and safely so that it won’t affect your garage door’s opening. You can get this done on your own and if you do not know how to do, then you can also call for a professional to help you in this. Also, make sure to check the tightness of the chain every now and then to make sure that there are no chances of any accidents or inconsistencies in the alignment of your garage or if it may be stuck on one side and not the other. You can use the garage freely without worrying about it.

How to Adjust a Garage Door Gap

There are plenty of reasons you’ll need to fix a gap on your garage door. Firstly, gaps can be a major security risk to your home as they are an invitation to burglars to try and force the door open and get inside. A gap can also be unsightly and affect your home’s curb appeal, especially if you’re looking to sell your home. It helps, therefore, to learn how to adjust a garage door gap.

How to Adjust a Garage Door Gap

This article outlines a few tips on adjusting a garage door gap. It outlines the items to check ranging from the stops to adjust limit switches to replace the seal.

Check the Stops

The stops refer to the rubber seals running along the edges of your automated garage door. They create a seal when your garage door is closed, keeping the weather out and preventing the door from staying open. If your garage door has gaps, it’s likely the stops aren’t aligned correctly on the door. You either have to get them replaced or moved closer to the gaps.

How to Adjust a Garage Door Gap

Look at The Tracks

Check whether the door is perfectly vertical when closed. If not, you’re likely to have gaps around the door. Fixing this is simple and you can even do it on your own. Start by looking at the vertical tracks that your garage door travels on. If they’re not holding the door at a consistent distance from the stops, adjust the door so it sits closer to the stops by loosening the mounting bolts and moving them slightly.

Adjust Your Limit Switches

Your limit switch determines where your garage finishes when you shut it. If the settings are not quite right, the door will have a gap and it can even cause your garage door to jerk. The flexible seal at the bottom can also affect the gap. The trick here is to adjust the limit switch so the seal is compressed to the floor, sealing the gap. The limit switch is usually found with the opener but be sure to read the instructions for your particular door opener as many have different settings. Your limit switch is also the easiest way to adjust your garage door height

Replace the Seal

If the seal is not sitting flush with the floor, that can also be a problem. This may be a result of wear and tear, which is quite normal with garage doors. You can replace a seal yourself. Pick up a new seal at your hardware store and follow the instructions to ensure it closes the gap correctly.

How to Adjust a Garage Door Gap

Trim the Door to Fit

Garage doors typically have a settling problem as it changes the way the door sits in the frame. If you have a wooden garage door, you can simply trim the door so that it fits properly. You can use a circular saw or jigsaw, sand off the bottom and replace it in the frame. If you don’t have a wooden garage door, you may be looking at a replacement.

Bottom Line

The points mentioned have covered most of the tips on how to adjust a garage door gap. Other options include installing a garage door threshold or adding more concrete to the floor. However, sometimes you may not be able to identify the cause and that’s when you need to call in a professional garage door installer.

Garage Door Hard to Open – DIY Solutions

Is the garage door hard to open? You might surely have encountered the same stubborn garage door problem at least once in your lifetime, right? You are not alone: this is a common issue among car owners, and it could happen to anyone. Sometimes, you think it was the broken garage door springs which make your roll up door hard to open, or that something else caused the garage door sticking. Whatever the case is, it seems okay for some owners to delay the issue, even though they do know they need a dented garage door repair right away. However, we are here to tell you that, no matter which case you are in, you should never wait too long to fix your door.  

Garage Door Hard to Open

There are many garage door problems and solutions to consider. In this article, we will talk about the garage door’s different parts (e.g. garage door springs) to explain why your garage door is difficult to open, or why is the garage door sticking. We intend to offer you some advice on how to fix the “temper” of your stubborn garage door, but you may probably need a professional dented garage door repair later on, especially if you haven’t carefully examined your door for years. 

Garage Door Springs

Garage door springs certainly serve as the system’s nerves behind the door’s functioning. However, nothing is immaculate – springs have their own lifespan too, and the garage door will not stretch properly and flexibly without them.

Garage Door Hard to Open

When the springs begin to break, it could cause serious issues over time. But there’s a way to examine their health: switch off your automatic door opener (if you have one) and roll up your door only halfway open. Does it still maintain properly? If not, don’t hesitate to call for professional help – this is a potential safety issue. Fixing the garage door springs can also help quite a garage door

Garage Cables

Impaired garage cables would also incur the malfunction. Make sure not to ignore any issues among the cables, especially because of the potential harm they may bring upon people. Most importantly, do not attempt to handle the cables solely by yourself. Call for in-time help!

Garage Door Rollers

The rollers also play a significant role in every smooth-functioning garage door, and it certainly needs to be repaired or replaced once they are out of their durability. It is also useful to apply some lubricating oil.

Damaged Parts

Any sort of physical impact over the years could incur serious concerns, which make your door dented or even distorted. Makes sure to install a new door when that happens.

Garage Door Tracks and Hinges

Tracks won’t last long, either. Loosened or seriously damaged tracks would also impair the proper function of the garage door. When that happens, it is the owner’s job to do a basic ceiling-to-door inspection and a general full check.

Garage Door Hard to Open

Another factor that may seriously affect the operation of the garage door is the damaged hinges, so replacement is a must for these. Applying lubrication oil on a regular basis would also help keep your tracks and hinges healthy.

FAQs

Why does my garage door get stuck?

Track malfunction could be a reason behind the faulty garage doors. If there’s anything stuck in the tracks, make sure to clean and remove it immediately.

Why is my garage door opening so slow?

You may want to adjust the speed setting of your door opener. To fix the issue, use a stepladder to reach the mechanical parts and lubricate it, especially if you haven’t done so for a long while, and then examine the speed again by opening and shutting the garage door a few times.

Are you still worried about your garage door being hard to open? Don’t worry: we believe that you’ve learned how to fix the stubborn garage door now. We sincerely understand your frustration when you find your roll up door hard to open (or garage door sticking), but this article will get you out of trouble in no time. When it comes to mechanical parts, from the smallest to the garage door springs, it is always necessary to do a full check and simply call for help whenever you need to, so as to make sure you’d acquire a professional dented garage door repair in no time.

What Size Do Garage Doors Come In

When shopping around for a garage door, it’s important to find the right size door for your garage. Garage doors come in all kinds of materials, styles, types and colors in standard sizes. However, it’s important to note that there are lots of standard sizes, depending on the size of your garage and your requirements. So what size do garage doors come in?

What Size Do Garage Doors Come In

This article outlines the various sizes of standard garage doors. It highlights the various categories of garage doors and their respective sizes.

Most garage doors come in standard sizes for the regular residential garage doors, commercial garage doors, double garage doors and large garage doors. There are even custom-made garage doors.

What Size Do Garage Doors Come In

Regular Residential Garage Doors

Single garage doors come in various sizes. Residential garage doors come in three main types of sizes: 10×7 feet, 9×7 feet and 8×7 feet. These sizes of garage doors are designed to fit garages with a single standard-sized car, van, truck or SUV. Most manufacturers have garage doors in these sizes.

Double Garage Doors

If you have vehicles that are slightly larger or you’d like to have more than one vehicle in your garage, then you’ll require double garage doors. They come in three different standard sizes: 16×7 feet, 14×7 feet and 12×7 feet. Double garage doors are also ideal if you’d like to utilize your garage as an additional storage space or workspace.

Large Garage Doors

If you have an RV, several cars or would simply like to utilize a really big space for your garage, then what you need is a large garage door. These types of garage doors come in 16×9 feet, 16×8 feet and can even stretch to as wide as 20 feet. This type of garage door is ideal if you’re planning to house an extra-wide vehicle, several cars or simply need an extra bit of space for your needs.

What Size Do Garage Doors Come In

Commercial Garage Doors

If you’re running a business and require really big commercial doors to house a fleet of cars, trucks or simply accommodate large deliveries, then you can get standard-sized commercial garage doors. Garage door installers will typically determine the appropriate size of door for your needs based on the vehicle fleet or number of trucks that you have. Contractors will also consider the side room and headroom requirements. In addition to offering you an appropriately sized door, a reputable installer will recommend the best solutions based on your garage door usage and specifications.

Hiring a Professional

Only a professional garage door installer will have the knowledge and expertise to ensure a proper installation of your garage door. Be sure to do your due diligence and only hire an expert who can ensure a proper installation the first time.

Bottom Line

With the tips mentioned, you can now answer the question: what size do garage doors come in? However, there’s much more to choosing the right garage door than just the size. You must consider how to maintain the garage door, different garage door panels, and the style garage you want. It always helps to consult an expert. An experienced garage door installer can help you to determine the most appropriate type of garage door for your needs. 

How to Measure for Garage Doors

Before you replace or buy, knowing how to measure for garage doors is crucial. It means you will get the right door for the garage. Its installation and operation should be easy as long as you get it right from the very start. 

how to measure for garage door

How to Measure for Garage Doors

Are you trying to get the measurements for your garage door? You have terrific timing. This post will take you through the measuring process. It will also throw in a few tips to make the process easy. 

Method #1: Measuring Garage Door

  1. Begin with the broadest part of the opening door. It should run from the right to the left end of the door. Keep your eyes open to notice any irregularities that may affect the dimensions.
  2. Get the height of the door opening. It should run from the top to the bottom of the door opening. Again, you should be aware of any irregularities that can affect the final dimensions and keep in mind if it is a single garage door or larger.
  3. It is time to get the widths for the rest of the parts other than the opening. You will need at least 5 inches on each side of the vertical part. If you are doing a double-door installation, then you will need a 10-inch width. 
  4. Get the dimensions for the top of the door opening and the ceiling. You can also go with the lowest part of obstruction for the ceiling. You should stick to the manufacturer’s headroom recommendations religiously. 
  5. Get the dimensions from the door opening to the nearest obstruction or the back of your garage. If you are installing a sectional door with manual lifting, the backroom space should not be less than the height of your door plus an extra 18 inches. For doors that will use an electric opening system, the backroom should be the door’s height plus an extra 4’2”. 

Method #2: Measuring Garage Door with Roll-Up Coiling

  1. Measure the widest width of the door opening from the left to the right side. Check for any imperfections that can affect the dimensions.
  2. Go for the vertical height of the door. It is the distance between the lowest part of the floor and the top of the opening. 
  3. Ensure you get right the side clearances for each door type. Each door type comes with clearance requirements from the manufacturer. 
  4. Measure the clearance for the headroom. Again, each door type will need a different clearance allowance. 
  5. Finally, get the backroom clearance depending on the type of door you want to install. 

Tips for Garage Door Measuring

  • Allocate and mark electrical outlets for the door opening
  • Be sure on the level of the floor
  • Look out for any irregularities that may affect the dimensions such as different types of hinges and other parts that are loose. 

Bottom Line 

It is useful to know how to measure for garage doors. It saves time and money because you will always get the right door for your garage. When measuring, make sure that any surface irregularities do not interfere with the dimensions and make sure that you’re following proper garage door safety tips as well. When you get the measurements right, the door should fit just like it belongs there. Note that different door types will require varying clearance sizes. If you need additional help when it comes to measuring your garage door, reach out to an expert to ensure that you’re getting it done correctly for when you’re installing a new garage door

Dented Garage Door Repair – How to Fix it

Garage doors are important as they help to keep your cars safe in the garage. Due to many reasons, getting a dent or two on your garage door is quite common. You will probably have to replace the entire garage door in case it has large dents. But if the garage doors have smaller dents, then you can repair or fix it yourself. For the dented garage door repair, you have to follow some steps which are very important. 

Dented Garage Door Repair

If you are looking for repair guidelines and solutions for a dented garage door, then you are at the right place. We are here to help you with all the step-by-step methods that you need to use to ensure that the dents are repaired. Once there are no dents, make sure to maintain your garage door to prevent future problems. To fix the small dents on your garage door, read on.

Repairing Garage Door Dents

To repair the dented garage door, you can follow different methods. Here are some of the methods and steps to be followed.

Method #1: 

Repairing Garage Door Dents

For this, you will need a wooden block, putty knife, rubber mallet, patching material, primer, paint and fine-grit sandpaper.

Steps to Follow:

  • First you need to wash the dented area properly with the help of warm water and detergent. Then allow it to fully dry down.
  • Now, you have to place the wood block over the dent and then tap it with the mallet for evening out the dent.
  • Then you have to sand the area and even it out.
  • You have to use a patching material for covering the area with the dent. Let it dry completely and then sand it down again.
  • After all these, you have to apply a primer and then let it dry. Once it is done, paint it.

Method #2: 

For this, you will need a heat source, aluminum foil and compressed air. 

Steps to Follow:

  • First you have to wash the area with the help of warm water and detergent solution. Let it dry completely.
  • Now put a strip of aluminum foil over this garage door dent.
  • Using a heat source, you have to evenly heat up the foil.
  • After few minutes, you have to remove the foil and then spray the dent with the help of compressed air for 30 seconds upside down.
Repairing Garage Door Dents

These two are the best methods for repairing the garage doors with dents. You can try both of these on your own. They are easy as well as quite fast to do. But if the dents are too big or too stubborn, then this may not be enough. While dents are not an uncommon garage door problem, make sure to inspect your garage door from time-to-time. You should also inspect the track system for dents, as this can cause your garage door to jerk when closing.

Conclusion

So, these are some of the best DIY dented garage door repair methods that you can try on your own. In case, the dents are too large to be handled, you have to call a garage door repair professional, or you can also replace the entire garage door. Either way, you have to hire a reliable service. But if the dent is manageable, you have to try out these methods and you can easily fix them on your own. You need to make sure that you are trying the methods that will suit perfectly according to your needs.

How to Quiet Garage Door

If your garage door is unnecessarily loud when opening or closing, then you need to take steps to quieten it. You may have completely soundproof your garage but a noisy garage door can still cause problems. Fortunately, there are several ways to make your garage door quieter. So, here are a few tips on how to quiet garage door.

How to Quiet Garage Door

This article highlights a few tips on making your garage door less noisy when it’s being opened or closed. It covers tips ranging from insulating the garage door and tightening loose bolts and nuts to investing in a garage door silencer to handle this garage door problem

Insulate Your Garage Door

Garage door insulation is primarily done for temperature regulation but it can also help to make your garage door quieter. Most garage doors are made from vinyl, aluminum or steel, none of which are good at minimizing vibrations. Insulating your garage door, therefore can help to reduce vibrations amplified by these garage door materials.

Tighten Screws, Nuts and Bolts

Over time, opening and closing your garage door can slowly cause nuts and bolts to loosen, leading to rattly garage doors or unaligned doors. Inspect your garage door panels for any loose screws, nuts and bolts and ensure they’re tightened thoroughly to keep your door moving smoothly and prevent any rattling sounds.

Lubricate the Door

It’s advisable to lubricate your garage door every year to minimize wear and tear and reduce noise by keeping it running smoothly. Avoid normal oil or WD-40 as they’re not designed for garage doors. Instead, buy a lithium-based oil. Apply the oil to the hinges, rollers, lock, bearing plates and springs, tracks and the rails.

Use a Quiet Garage Door Opener

Investing in an automatic garage door can make it easy for you to drive into your garage. However, garage door openers differ, particularly when it comes to noise levels. For instance, belt-driven garage door openers make much less noise than their chain-driven counterparts. Modern garage door openers use DC powered engines which are quieter than some older models that use AC powered engines. As such, switching from an old door opener to a newer, less noisy model can help to make your garage door quiet.

Invest in a Garage Door Silencer

A garage door silencer can help to make your garage door quieter. Even the quietest openers create some vibrations when in operation. Pairing your opener with a silencer, therefore, helps to reduce the overall noise levels of any garage door. Silencers work by decoupling your garage door opener from your ceiling. As a result, this dampens vibrations and lowers noise levels significantly. They’re relatively easy to fit but you have to detach your door opening machine so if you’re not up to the task, seek professional help.

Bottom Line

A noisy garage door can be a nuisance, especially if people are sleeping above the garage and someone has to leave the house in the early hours. The tips mentioned on how to quiet garage door will go a long way in reducing the noise from your garage door opener. Other options to consider include replacing your garage door side and bottom seals, replacing extension springs with torsion springs and replacing rollers with quieter nylon rollers.